Interface and Peripherals
Hand soldering Micro USB connector can be a daunting task, if it is even possible at all. That's why you will need this Micro USB Breakout board if you will be building a project that has a Micro USB port...
₱15.50
USB Host ADK Module adds USB host capability to your microcontroller (gizDuino/Arduino) based project easily.Power Supply: 3.3VDCInterface: SPISupports HUB function communication with Android and other USB devices...
₱700.00
Snap quick learning board for gizDuino/Arduino.This board contains:- 4-Digit seven segments with Drivers- Push Button Switch (3)- Buzzer-LED indicators (4)And socket for additional devices (not included) like- IR Sensor- Voice Recognition Module- LM35 temperature sensor- Servo Motorand many more dev..
₱162.00
SPI microSD Card Readerwith on board 3v3 Regulator and Level converter.The on board level converter and regulator allows you to use the board directly to a 5V microcontroller systemlike the gizDuino and Arduino boards.Downloads :Manual
Link..
₱49.00
Pre-order
DS3231 Real Time Clock Module with BatterySmall form factorPower: 2.3-5.5VDual calendar alarm, +/-3? accuracy of digital temperature sensorHigh-speed(400kHz) I2C serial bus1Hz and 32.768kHz output reset button debounced input and output.Downloads :DS3231 Arduino Library
Downloads..
₱110.00
Pre-order
DS3231 Real Time Clock Module withAT24C32 EEPROMPower: 3.3-5.5VDual calendar alarm, +/-3? accuracy of digital temperature sensorHigh-speed(400kHz) I2C serial bus1Hz and 32.768kHz output reset button debounced input and output.Note: Battery not included and is sold separatelyDownloads :..
₱119.00
Ethernet LAN Shield Module- Wiznet W5100 Chip- Built-in IP stack TCP and UDP- Compatible with Arduino Uno and Mega- Micro SD card slot- 10/100 Base-T- 5V Supply VoltageDownloads :Ethernet Library from Arduino
DownloadsModified Ethernet Library
DownloadsModified SD Library
..
₱496.00
-16 %
Backplane/Development board for NodeMCU Ver 3With on board 5V input voltage regulator...
₱105.00 ₱125.00
Brand: e-Gizmo
FT2232 Breakout BoardUSB 2.0 bridge to UART,JTAG,SPI,I2C, and Parallel I/O.On board 3.3V 150mA LDO voltage regulator.Equipped with dedicated JTAG port for use as LCMX02 FPGA programmer kit.Useful Links:FTDI FT2232H Support PageDatasheet, drivers, DLL, application notes related for this product can b..
₱850.00
This passive buzzer module has a built-in driver, hence you can connect its input directly to a has controller. Note that this is not a stand alone buzzer, it requires a driving signal form a host controller. This buzzer is at its loudest when driven with a 2Khz-5KHz square wave. Compatible with all..
₱27.00
-41 %
Pre-order
Brand: e-gizmo
Rotating controls are our most ergonomic way of adjusting something, and is the preferred method over push buttons, especially when it involves fast and repeated adjustments. (For example, a potentiometer for volume control.) But digital circuits are not exactly well suited for analog potentiometer ..
₱75.00 ₱127.00
This is a low cost USB to TTL module based on CH340 chip. CH340 is low cost alternative to FTDI USB serial Chips. The Module supports both 3.3V and 5V levels by a jumper selection. The module supports 50bps to 2Mbps baudrates.
Specifications :Power Input
USB PortData Interface
Serial ..
₱56.00