Motor Drivers
New
The ULN2003 Stepper Motor Driver Module is a compact, highly popular electronic board designed to bridge low-power microcontrollers (like Arduino, ESP32, or Raspberry Pi) with higher-current unipolar stepper motors.Built around the ULN2003 Darlington transistor array chip, it amplifies weak logic si..
₱58.00
New
If you’ve ever tried to build a hexapod walker or a complex robotic arm using just an Arduino, you’ve likely hit a wall: not enough pins. Most microcontrollers tap out after a few servos, leaving your ambitious project literally paralyzed.Enter the PCA9685 16-Channel 12-bit PWM Driver. Think of this..
₱240.00
Motor Controller for 100W-500W 3-phase Brushless DC Motors. Note: This version has no input for Hall Sensors.Operating Voltage: 12-36VDC (Note 1)Operating Current: 15A Max.Output Capacity: 500WSpeed Control Input Voltage: 0-5VDCHall Sensor Input: NONENote 1: Although the manufacturer rates this for..
₱485.00
Pre-order
Brand: e-Gizmo
Speed/Power controller for brush type DC Motor.Working Voltage: 6V-90VDCPower Output: 0.01-1000WMaximum Output Current: 15AStandy Current: 5mA TypicalPWM Duty Cycle: 0-100%PWM Frequency: 15kHzUseful link:6-90V 15A PWM DC Motor Speed controller Review and Testing with different motors
Yo..
₱240.00
Pre-order
This 3-phase Brushless DC Motors controller, although primarily designed for e-bikes, works just as well with many other DC brushless motors used for DIY projects.Operating Voltage: 36/48VDC Auto-selectOperating Current: 15A Max.Output Capacity: 350W maximumSpeed Control Input Voltage: 0-5VDCHall Se..
₱556.00
Motor Controller for 100W-500W 3-phase Brushless DC Motors. Operating Voltage: 12-36VDC (Note 1)Operating Current: 15A Max.Output Capacity: 500W (Note 2)Speed Control Input Voltage: 0-5VDCHall Sensor Input: 0-5V LogicNote 1: Although the manufacturer rates this for up to 36VDC, It is recommended to..
₱475.00
Pulse Width Modulation DC Motor Speed Controller.For DC Brush Motor OnlyOperating Voltage Range: 4.5VDC - 35VDCStandby Current: 7uA TypicalOutput Current: 5A MaximumRated Output: 90W maximumPWM Frequency: 20KHzDuty Cycle: 1-100%Package: 1x PWM Module1x Knob1set Potentiometer NutWeight: 15gDimensions..
₱54.00
2-Channel L9110S Motor Driver- Independent control of two DC motors - Alternatively, it can also be used to drive single bipolar (4-wire) stepper motorPower Supply Voltage: 2.5-12VDCMaximum Drive current: 800mA per outputTTL/CMOS compatible drive inputs..
₱50.00
This general purpose motor driver has two independent drivers that can be used to PWM speed control up to two DC brush motor, or as a driver for single bipolar stepper motor.Driver Chip: TC1508SOperation Voltage: 2V-10VDCCurrent: 1.5A Cont, 2.5A peakInput Logic Level: 5V Logic..
₱39.50
-4%
Pre-order
The **L293D Motor Driver Shield** is a device that can be used to control DC, stepper, and servo motors using an Arduino board. It is compatible with the Arduino UNO and MEGA boards. The shield features two L293D motor driver ICs and one eight-bit shift register chip. The L293D IC is a low-voltage o..
₱134.00 ₱140.00
Brand: e-Gizmo
8A DC Motor DriverOperating Voltage : 6V to 24VDCDevice : VNH5050A Peak Drive: 30 Amps (internally limited)Drive Ampacity: 8 Amps w/ heatsink 4 Amps no HeatsinkOverload Ampacity: 8 Amps for 25 secs (no heatsink) 10 Amps for 45 secs (with heatsink)Fault Indicators: Output Short Circuit Thermal Shu..
₱430.00
ESC Electronic Speed Control for high speed brushless DC motors. PWM Speed control input, square wave output.Note: Be careful when working with high speed, high power Brushless DC motor. Mishandling can cause serious injuries.
Features :BEC Power: YesCut-off voltage: 4VBEC..
₱363.00