3 Channel Line Tracker Sensor1 FAQ Designed for Mobile Robot line tracking applications, five or three infrared reflective sensors CNY70 will reliably detect dark lines printed over light color surface. Detection distance >10mm from sensor face is possible. Adjustable sensitivity for each
3-Axis Digital Accelerometer ( ADXL345 )1 FAQ Break-out board for ADXL345 3-axis accelerometer requires low power with a high resolution of 13 bits.It has a programmable range of resolution specially +/-2g,+/-4g,+/-6g,+/-8g and +/-16g.
4 Direction / Tilt Sensor1 FAQ Direction/Tilt sensor breakout board based on Rohm RPI-1031 sensor. Detects x-y tilt or motion in 4 quadrant direction. Two- bit Logic outputs latches and indicates the most recent motion direction.
5 Channel Line Tracker Sensor1 FAQ Designed for Mobile Robot line tracking applications, five or three infrared reflective sensors CNY70 will reliably detect dark lines printed over light color surface. Detection distance >10mm from sensor face is possible. Adjustable sensitivity for each
AC Power Analyzer MK II with case3 FAQs New and improved Power Analyzer Kit that can be interfaced with any USART equipped microcontroller or PC. It can be easily configured as a stand alone power measuring equipment when used with a Serial LCD II kit.
ACS Current sensor (ACS-711T)4 FAQs e-Gizmo ACS71x Current sensor is a Hall effect-based linear current sensor the on-board IC from Allegro with current fault output. Solutions for AC or DC current sensing in less than 100V. Typical applications include circuit protection current monitoring
Bio-Amp Sensor Circuit2 FAQs e-Gizmo Bio-Amp Sensor Circuit is an instrumentation amplifier designed to pick-up minute electrical voltage by living biological organ like the human body. Its main feature is the use of Signal Opto-Isolation and high CMRR instrumentation amplifier outpu
Compact IR Proximity-Collision Sensor3 FAQs Detects objects as far as 72mm (2.8 inches) from the sensor face. Infrared beam makes it relatively insensitive to ambient light and color (of target object). Applications includes non contact object detection and collision sensor for mobile robots.
Gas Sensor Kit ( MQ-2 )2 FAQs MQ-X Gas Sensor Kit allows you to calibrate and detect gaseous substances depending on the on-board MQ-Series Sensors ( MQ-2, MQ-5, and MQ-7 ). With HIGH, MEDIUM, and LOW Digital Output with LED Indicator per output and had on-board potentiometer for easy
Gas Sensor Kit ( MQ-5 )1 FAQ MQ-X Gas Sensor Kit allows you to calibrate and detect gaseous substances depending on the on-board MQ-Series Sensors ( MQ-2, MQ-5, and MQ-7 ). With HIGH, MEDIUM, and LOW Digital Output with LED Indicator per output and had on-board potentiometer for easy
Gas Sensor Kit ( MQ-7 )1 FAQ MQ-X Gas Sensor Kit allows you to calibrate and detect gaseous substances depending on the on-board MQ-Series Sensors ( MQ-2, MQ-5, and MQ-7 ). With HIGH, MEDIUM, and LOW Digital Output with LED Indicator per output and had on-board potentiometer for easy
Gauge Pressure Sensor 0 FAQs Our new Gauge Pressure sensor breakout board featuring Small size and Low Power Consumption with 0 to 37 kPa Pressure range. Application examples for leak detection, pressure controller, level indicator
Note : Must be interface with e-Gizmo Sensor Ampl
Heart Rate Monitor Kit2 FAQs The e-Gizmo Heart Rate Monitor kit a simple pulse sensor to your finger tip and ready to read your heart rate. A very useful design for studying your activity and monitoring your heart beat..
Light and Dark Sensor1 FAQ e-Gizmo Light & Dark sensor a simple sensor with 2 functions in 1 board. With digital output pin connection and DPDT switch for light and dark sensed selection modes. Adds-on to your project for automatic light on/off with your favorite gizDuino MCU board
Line Array for P-BOT Board 0 FAQs PBOT's Dedicated Line Array sensor composed of 3 CNY70 Photo electric sensor that is applicable for line tracing robots.
Note : This Sensor is sole Compatible with e-Gizmo PBOT Board.
Metal Detector kit ( Pulse Induction PI detection method )2 FAQs Our new e-Gizmo Metal Detector kit can detect metallic object as small as 2x2mm (tested object - screw) located about 2 cm above the plane and center of the sensing coil. Larger objects can be sensed at a longer distance.
Sensor Amplifier Kit1 FAQ Sensor Amplifier or so called Instrumentation amplifier is a type of differential amplifier because of its great accuracy and stability output for the sensor. It is an amplifier that particularly use in measurement and test equipment. It acts as a bridge
Smoke Sensor2 FAQs Smoke sensor detects the presence of smoke by measuring the drop in current in the ionization detector (HIS-07). The ionization detector uses Americium as a source of ionizing radiation for ionizing oxygen and nitrogen in the air that normally generates a
Soil Moisture Sensor2 FAQs Our new soil moisture sensor with sturdy stainless steel probe for measuring the amount of water in the soil. It has a presettable one bit digital output -for simple and quick application that only need a wet or dry binary equivalent sensing, and an analo
Sound Activated Switch1 FAQ e-Gizmo Sound Activator Switch were you can control your devices by using a snap of you finger or clap to make a noise or sound. Its very useful requires only +5VDC for the supply input and an output pin connection for high or low logic control. Compatibl
Temperature Control Unit Display4 FAQs The e-Gizmo temperature control unit display is made for easy and fast measurement circuit temperature sensor, whose output voltage is linearly proportional to the Fahrenheit on its LM34 IC sensor then converted / calibrated directly in degrees celcius.
Through Beam Sensor3 FAQs Detects objects passing in between the sensor transmitter and receiver modules. Sensor modules can be separated up to more than a meter. Use it to detect objects in conveyor line system, pass through security, etc..
Water Level Sensor3 FAQs The new water level indicator with sturdy stainless steel probe also for detecting the level of water. With its simple 3-LED status indicator, and gives out a digital output. Compatible in all gizDuino boards. Input supply +5VDC.
3-Axis Gyroscope Break-out Board2 FAQs Break-out board use of ITG3205 which functions as a 3-axis MEMS gyro IC. It is frequently optimized for gaming such as 3D mice and 3D remote control applications.
37 in 1 Sensor Kit for Arduino 0 FAQs 37 in 1 Sensor Kit for Arduino (Please see Important Note detailed below before ordering)
http://www.e-gizmo.net/oc/index.php?route=product/product&path=59_66_107&product_id=1310
6 Degrees of Freedom1 FAQ 6DOF is a combination of an accelerometer and a gyroscope together in one break-out board. Chips can also be used individually by the use of I2C or SPI interface.
APDS-9930 Digital Proximity & Ambient Light Sensor1 FAQ The APDS-9930 provides digital ambient light sensing (ALS), IR LED and a complete proximity detection system in a single 8 pin package. The proximity function offers plug and play detection to 100 mm (without front glass) thus eliminating the need for fac
Coin Slot for ₱?1, ₱5, ₱103 FAQs Add Coin slot Function to your project! our coin slot module for ?1, ?5, & ?10 is the best fit for projects like kiosks and other related projects.